"6F22" is the international (IEC) code for the standard rectangular 9V battery. HW Energy supplies it as the 9V 6F22 Heavy Duty battery, a zinc-manganese dioxide cell built for low-drain, cost-sensitive devices.
Short answer
Choose the 6F22 for 9V devices that draw little current or run only occasionally, where unit cost matters more than maximum runtime.
Choose the alkaline 9V 6LR61 for smoke alarms, anything that must not fail, cold environments, or higher current draw. HW Energy's own selection guide lists smoke detectors under alkaline.

What "6F22" actually tells you
Under the IEC 60086 naming system, 6F22 describes a zinc-carbon rectangular battery made of six flat "size 22" cells, equivalent to the cell sold as PP3.
The code identifies size and chemistry family only. It says nothing about capacity or build quality, so two batteries marked 6F22 can perform very differently. That is why the published data below matters more than the label.
Verified specifications
Table 1 uses only values published on the HW Energy 9V 6F22 product page.
| Parameter | Published value | What it means for you |
|---|---|---|
| Designation | 6F22 (IEC) / 1604D (ANSI) | Standard 9V size; fits any device specified for a 9V or PP3 battery. |
| Positive active material | Manganese dioxide (EMD) | Electrolytic manganese dioxide, the same cathode material class HW Energy uses in its alkaline cells. |
| Negative active material | Zinc (Zn) | Zinc is the source of the cell's electrons. |
| Nominal voltage | 9 V | Same nominal voltage as a 9V alkaline, so it is electrically a drop-in replacement. |
| Operating temperature | −20 °C to 45 °C | Suited to indoor and moderate outdoor use. Expect reduced output in the cold. |
| Packaging options | Blister card, shrink wrap, paper box, industrial packaging | Covers retail shelves, multi-packs and bulk supply to manufacturers. |
What the page does not state: rated capacity, weight, exact dimensions, shelf life and discharge curve are not published for the 6F22. For a specification sheet or a purchase contract, request the technical data sheet from HW Energy rather than relying on the class figures below.
A detail worth knowing: HW Energy's general selection guide lists −10 °C to +50 °C and "poor" cold performance for the heavy duty class, while the 6F22 page states −20 °C to 45 °C.
How much runtime to expect
Capacity in a zinc-carbon 9V is not one fixed number. It falls as the current you draw rises. The two published datasheets below, for 6F22-class cells from other manufacturers, show the effect clearly. They use different test conditions, so read them as an illustration of the trend and not as a ranking of brands.
| Reference datasheet | Test load | Rated capacity | Implied continuous runtime |
|---|---|---|---|
| Energizer EVEREADY 1222 (6F22, super heavy duty) | 5 mA continuous, to 4.8 V, 21 °C | about 400 mAh | about 80 hours |
| Longlife 6F22 specification | 620 Ω, 24 h/day, to 4.8 V, 20 °C (about 14.5 mA at 9 V) | about 150 mAh | about 10 hours |
Runtime = rated capacity ÷ load current. The 14.5 mA figure is 9 V ÷ 620 Ω at the start of discharge.
Two practical consequences
- Estimate before you buy. Divide the capacity at your device's current by the average current. A device drawing 5 mA for 2 hours a day uses 10 mAh a day, so a 400 mAh cell gives a ceiling of roughly 40 days. Real life is lower, so treat it as an upper bound.
- Check your device's cut-off voltage. Datasheet capacities are measured down to 4.8 V (0.8 V per cell). A zinc-carbon cell's voltage declines gradually as it discharges, so a device that stops working at 7 V will use much less of the rated capacity than the datasheet suggests.
At very low currents the limit shifts from capacity to ageing. HW Energy's selection guide cites roughly 6–10 % self-discharge per year for zinc-chloride heavy duty cells, against about 2–3 % for alkaline. Paying for capacity the cell will never get to use gains nothing.
6F22 heavy duty vs 6LR61 alkaline
HW Energy makes both chemistries in the 9V size. Table 3 sets them side by side using the company's own published data.
| Attribute | 9V 6F22 Heavy Duty | 9V 6LR61 Alkaline |
|---|---|---|
| IEC / ANSI code | 6F22 / 1604D | 6LR61 / 1604A |
| Active materials | Zn / EMD manganese dioxide | Zn / EMD manganese dioxide |
| Nominal voltage | 9 V | 9 V |
| Operating temperature | −20 °C to 45 °C | −20 °C to 45 °C |
| Published capacity | Not published on the product page | 550 mAh (35 mA, 24 h/day, 20 °C, 0.8 V per cell end voltage) |
| Published weight | Not published on the product page | Approximately 44 g |
| Shelf life (HW Energy selection guide, class level) | 3–5 years | 7–10 years |
| Best suited to | Low-drain or occasional-use devices, cost-sensitive supply | Higher-drain, long-standby and critical devices, cold environments |
Capacity figures measured under different conditions are not directly comparable. Do not compare the 550 mAh alkaline figure with the class figures in Table 2.
Which one should you buy?
Choose the 6F22 when
- The device draws a small current or is used in short sessions.
- You replace batteries more than once a year anyway. HW Energy's rule of thumb for its heavy duty range is that this pattern usually gives the best cost per hour.
- You are an OEM or distributor who needs an economical 9V for a price-sensitive product.
Choose the alkaline 6LR61 when
- The device is a smoke alarm or any safety device. HW Energy's guide recommends alkaline for these. Always follow the alarm manufacturer's stated battery type as well.
- Batteries sit in the device for long periods, or you rarely change them.
- The device runs in cold conditions or draws a higher, steady current.
Not sure about your device's current? Check the manual, or measure it with a multimeter in series. The alkaline vs carbon zinc selection guide explains the drain bands in more detail.
Safe storage, use and disposal
A 9V battery needs more care than an AA, because both terminals sit side by side on one end. If a metal object touches both, it can short-circuit and generate enough heat to start a fire.
- Store in the original packaging until use. If loose, cover the terminals with masking, duct or electrical tape, and never keep them in a drawer with paper clips, coins or other metal.
- Keep it cool and dry, below 25 °C and out of direct sunlight, as HW Energy advises.
- Do not mix old with new cells, or different chemistries, in the same device. Remove batteries from equipment that will sit unused. HW Energy explains why leaks happen in its leak prevention article.
- Tape the terminals before disposal. The U.S. EPA says alkaline and zinc-carbon batteries can safely go in household trash in most communities, but recommends recycling them or checking with your local solid waste authority.
Buying checks: confirm you have the genuine product
"HW" is used as shorthand by more than one battery brand. For example, one online listing for an "HW heavy duty 6F22" names the brand Hi-Watt and gives the origin as Guangdong, China. HW Energy states that its cells are made in Vietnam.
When you receive a sample or a shipment, check:
- Manufacturer name, "6F22" marking and country of origin on the label.
- Size within the standard 9V envelope, about 48.5 × 26.5 × 17.5 mm at maximum according to published manufacturer datasheets.
- No leakage, deformation or damaged jacket. A sample 6F22 specification from another maker lists this as a basic acceptance requirement.
- A batch or date code you can quote back to the supplier.
About the manufacturer
Knowing who makes a battery matters as much as the datasheet. According to the HW Energy About page:
- A US$50 million investment from HW International Singapore and more than 30 years of industry experience.
- A facility built in 2024 in Vietnam with 14 high-speed smart lines, over 55,000 m² of floor area and a capacity above 2 billion pieces.
- The only integrated manufacturer in Southeast Asia with full-scale production of both alkaline and carbon-zinc batteries, with every AA, AAA, C, D and 9V cell marked "Made in Vietnam".
- Raw materials sourced from Belgium, France, Japan, South Korea, China and Vietnam.
The smart manufacturing page describes more than 50 critical inspections across the production journey and a laboratory with over a hundred instruments. The company's certification section shows ISO 9001, ISO 14001, C-TPAT and WCA credentials. Note that these certify the company's systems and facility, not the runtime of any single battery. For product performance, rely on the technical data sheet.
On the environmental side, the plant sits in the Deep C Industrial Zone in Haiphong, whose electricity network includes solar, waste-to-energy and wind power, and the sustainability page lists Nordic Swan Ecolabel and FSC credentials.
For OEM, private label and bulk buyers
- Packaging: the 6F22 is offered in blister card, shrink wrap, paper box and industrial packaging.
- Lead time: HW Energy's FAQ states 90 days for a first order and 60 days for repeat orders.
- Customisation: the customization service runs from jacket and packaging design through sample confirmation, production, quality inspection and delivery. See also the quality management section.
- Regulation: the FAQ says HW Energy can make carbon-zinc batteries that comply with the latest EU regulations. The 14th edition of IEC 60086-1 (June 2026) replaces the 2021 edition and adds an annex supporting the EU Batteries Regulation 2023/1542.
To request samples, a quotation or a datasheet, use the inquiry form on the 6F22 product page or the contact page. Phone: 0084-225-82212198. Email: info@hwenergy.vn.
Frequently asked questions
Is a 6F22 the same as a 9V or PP3 battery?
Yes for size and voltage. 6F22 is the IEC code for the standard rectangular 9V cell, equivalent to PP3.
Is the 6F22 rechargeable?
No. It is a primary (single-use) zinc-manganese dioxide cell. Never try to recharge it.
Can I use it in a smoke alarm?
Check the alarm's manual first. HW Energy's selection guide recommends alkaline for smoke detectors, so the 9V 6LR61 is the safer choice.
What temperature range is it rated for?
The product page lists −20 °C to 45 °C.
How long will it last in my device?
Divide the cell's capacity at your device's current by the average current, then treat the result as an upper limit. Table 2 shows why capacity falls as current rises. For a guaranteed figure, request HW Energy's technical data sheet.

